Just How to Install a Bathtub Yourself
Just How to Install a Bathtub Yourself
Blog Article
How do you really feel about How to Install a Bathtub?
Setting up a bath tub isn't exactly rocket science, however it does need solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the project can relocate immediately; if you need to open up a wall to get rid of the old tub and also position the new tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will need a helper to leave the old tub and set in the brand-new one. See to it you have actually qualified yourself for the task and also fit trying it. Instead of employing a specialist to take over a halfway-completed job, it is better to think about utilizing one prior to you start. Possibilities are you might require an expert plumber to make tube connections.
This short article will help you install a brand-new tub in your shower room if you have currently gotten a new tub as well as don't need to change the arrangement of your previous water supply pipelines.
Your devices as well as material checklist ought to comprise the following:
Preparing for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent strain on the tub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome because of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly come from the pipes. Once the supply pipes have actually been removed, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Using the two wood boards under its feet, place the tub in the called for placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub till the level checks out degree.
To mount faucets, fit all-time low of the outermost flexible tap adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water system and also examine all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise inspect the overflow outlet as well as the regular electrical outlet for leakages.
Finally, repair the bath paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been made use of a minimum of when as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, triggering the water to penetrate the wall in between the bath and also the tiling, bring about issues with dampness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to allow for the motion experienced when the tub is in usage. The sealant can split relatively very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our article about Installing A Bathtub. Thanks a ton for taking the time to read through our short article. Loved our article? Please share it. Let another person locate it. We thank you for reading our article about Installing A Bathtub.
Request Appointment
Report this page